Clone-A-Willy DIY Penis Molding Kit

Wish your man was around more often? Or maybe just his lower half? With the Clone-A-Willy® DIY Penis Molding Kit, you can have a vibrating silicone replica of his bits to enjoy whenever you like!

This kit contains everything you need to create a life-size, highly detailed replica dildo of any penis (with optional vibration), all in the comfort of your own home. The Clone-A-Willy Kit is free from latex and phthalates, and uses only top-quality body-safe materials, including algae-based moulding powder and odourless platinum cure silicone. Just add water and you’ll have all-hours access to your partner’s genitals, anytime, anywhere!

The Clone-A-Willy Penis Molding Kit can accommodate penises up to 9 inches in length and 2.5 inches in girth, and comes in a wide range of colours to choose from to suit your every mood, including:

• Light Skin Tone
• Medium Skin Tone
• Deep Skin Tone
• Neon Purple
• Hot Pink
• Black

The Clone-A-Willy DIY Penis Molding Kit is the perfect gift for bachelor and bachelorette parties, Valentine’s Day, anniversaries, farewell parties, and much more. This quick and easy project is great for DIY fun together, or as a surprise for your lover! With your lifelike replica of your partner’s parts, you’ll never have to be without them again!

Key features of the Clone-A-Willy DIY Penis Molding Kit:

• Creates a highly detailed, life-size replica of any penis
• Top-quality body-safe materials & ingredients with no odour
• Latex- & phthalate-free for users with skin allergies
• Includes an optional vibrator to make your dildo vibrate
• A quick & fun DIY project to do together or as a surprise for your partner

How to use the Clone-A-Willy DIY Penis Molding Kit:

1. Starting with an erect penis, hold the permanently sealed end of the tube against your body and mark where your penis reaches on the tube, then cut the tube to size by removing the excess. (Since the edge you just cut will be pressed against your body later, we recommend wrapping some tape over any jagged cuts so the tube feels smooth and comfortable against your skin.)
2. This step and the next are temperature-dependent, so make sure you’ve read the instructions and you’re ready to work quickly!Heat some water to exactly 32°C, then pour 415ml (or 1 and ¾ cups) of it into a large mixing bowl. Set a timer for 2 minutes, then immediately pour the bag of moulding powder into the water and start mixing, stirring for no longer than 60 seconds — it’s normal for the mixture to still be a bit lumpy at this stage.
3. Pour all of the mixture into the moulding tube, then insert your erect penis into the tube while pressing it firmly against your body. There may be some spillage, so we advise you use your Clone-A-Willy moulding kit in the kitchen, bathroom, or with a tarp down. Your penis must be inside the tube before your 2-minute timer is over, otherwise the moulding powder will set before you get a chance to shape it.
4. If your penis is touching the side of the tube, rotate or angle it for a more central placement. Wait a few minutes for the mould to solidify, then gently remove your penis from the tube and leave your new penis mould to air-dry for at least 2 hours.
5. Empty the two jars of liquid silicone into a clean, disposable container. Use the included stir stick to get as much of each liquid out as possible, then stir them together for at least 2 minutes before pouring into the moulding tube until it’s about an inch (2.5cm) from the top.
6. If you want to add the included vibrator to your DIY dildo, make an X-shaped cut in a small cardboard square, then push the vibrator tip-first through the X until the cardboard is sitting just above the control dial. Insert the vibrator tip-first into the silicone until the cardboard hits the lip of the tube, making sure it doesn’t touch the sides of the mould, then leave it to set for 24 hours. After 24 hours, check to see if the silicone has fully cured, then remove your new DIY dildo from the moulding tube and enjoy!

Size:

• 22.86cm / 9″ maximum insertion depth
• 27.94cm / 11″ overall tube length
• 6.35cm / 2.5″ overall tube width

Battery & Power Information:

• Vibrator takes 1x AA battery (included)